How To Upgrade A Yamaha FJR1300 Clutch To 2016 Slipper With Easy Pull - This is a complete how-to vid showing you everything you need to convert your 2015 & prior Yamaha FJR1300 to the new 2016 slipper version. This also gives you a clutch pull roughly 1/2 that of the previous years for a MUCH easier time especially in stop and go traffic.

Total parts cost is just under $300 as of the time of this video. The graphic shows all the parts you will need to order circled in red, order from your supplier of choice.

The order of part assembly for the stack is as follows:

On the basket, the flat washer then the sloped washer - note the printing, it slopes down. Then a new thin friction plate, a new clutch plate then the retaining wire.

With the basket in the engine, 4 pairs of new thick friction plates and clutch plates. Then another new friction plate and 1 of the OLD clutch plates. Then a new thick friction plate, new clutch plate, finishing with a new THIN friction plate.

On the spring assembly, a new thin friction plate then a new THIN clutch plate.

WARNING - make SURE you carefully remove the ball bearing behind the small pushrod after you remove it, and replace it when reinstalling.

NOTE - holding the rear brake should also stop the rear tire from moving, to remove/install the main nut. If you choose to use the 5th gear/someone sitting on the bike method of removing the center nut, you DO RISK DROPPING THE BIKE as it will be moving forward under pressure. Installation is safe.

Torque specs for the center nut are 65 lbs./ft, inner spring bolts 5 (good and snug) and cover 8.7 (very snug).

Parts list: [ Ссылка ]

Visit [ Ссылка ] for all the new content!

My Bike Reviews:
[ Ссылка ]

My How-To Videos:
[ Ссылка ]

My Vlogs:
[ Ссылка ]

Gear Overview Videos:
[ Ссылка ]

All AIMExpo 2014 Coverage:
[ Ссылка ]

Leesburg Bikefest 2015 Videos:
[ Ссылка ]-



Follow on Facebook: [ Ссылка ]
Some music by ichillmusic.com

Join My FJR Enthusiasts group: [ Ссылка ]

AIMexpo 2015: [ Ссылка ]

If you have a common question it is probably answered here: [ Ссылка ] .
Police Motorcycle Competition:
[ Ссылка ] .

My editing/gaming build consists of:
[ Ссылка ]
My FZ09 / MT09 Mods:

Front Cowl: [ Ссылка ]
Fog Light Kit: Yamaha Part BS2854A30000
Fog Light Bracket: Yamaha Part BS2854A50000
EBC HH Pads NEED 2 SETS: [ Ссылка ]
Radiator Guard: [ Ссылка ]
LED Signals NEED 2 SETS: YME-W0789-00-00
LED Flasher Relay: [ Ссылка ]
Gilles Tooling Brake Lever: [ Ссылка ] Yamaha Part 1RC-H39A0-V0-00
Gilles Tooling Clutch Lever: [ Ссылка ] Yamaha Part 1RC-H39B0-V0-00
Rizoma Reverse Retro Mirror NEED 2: [ Ссылка ] Part BS070B
Rizoma Bar adapters NEED 2 Part LP300B
Rizoma Universal Bar Ends Pair: [ Ссылка ] Part MA534B
Yoshimura R77 Full Exhaust WORKS Finish: [ Ссылка ]
USB Port & Pigtail Kit: [ Ссылка ]
X-Grip: [ Ссылка ]
RAM Mount: [ Ссылка ]
Short RAM Arm: [ Ссылка ]
Rubber Footpegs: [ Ссылка ]
Yamaha Comfort Seat: [ Ссылка ] Part BS2F47C0V000
Quickshifter Part BS2E81A0V000
[ Ссылка ] Full Suspension & Brake Relocate Kit
[ Ссылка ] ECU Flash & Dyno Tune
Nelson-Rigg 2015 Magnetic Tank Bag: [ Ссылка ]
Nelson-Rigg Sport Tail Bag: [ Ссылка ] Some background music by www.ichillmusic.com #motorcycle #motorcycles #howto #motovlog #review
As an Amazon Associate I earn from qualifying purchases.

свернуть