This video goes over ONE possible cause for an erratic (crazy spinning needle) fuel gauge for old body style (OBS) GM trucks and vans of the 1990s and early 00s from Chevrolet, GMC, Holden, & Cadillac not working. In many cases the vibrating, twitching, bouncing, fluttering, and related unexpected jumpy behavior from the gauge has nothing to do with electrical grounds or the fuel tank sender, it is simply the effect of age on the aircore motor of the gauge itself. The original internal dampening effect is lost, corrosion sets in and the air core motor gauge becomes unreliable and must be replaced. Note that I said "aircore motor", there are NO stepper motors in these years!
The vehicle illustrated is an OBS (old body style) 1999 Chevrolet K1500 Suburban with the 6.5L diesel engine, but the symptoms and repair procedure apply to all GM trucks and vans of the same general era - before the introduction of stepper motors beginning in model year 2003. Of course the cluster disassembly I show is 96+ OBS only.
These motors were *never* sold by GM. NEW ones are in an OFF WHITE plastic housing color, whereas the originals were typically a yellow color. You have to pay attention to the calibration code letter in black on one of the housing ears as shown in the video. But DO NOT BUY USED yellow original ones - the air-core motor calibration is from a fluid internally that degrades with use and age so every original has the dampening defect to some degree as well as corrosion - so you'll be risking a failed repair by buying used. You can only fix the erratic behavior reliably by installing an (NOS) NEW air core motor OR a speedo shop remanufactured one. *Each GM gauge type uses a different aircore motor calibration, so again please take note of the letter codes below!*
Original calibration codes:
F = Fuel gauge (94-02 OBS trucks only)
C = Fuel gauge (1999-02 NewBS trucks only)
P = Oil Pressure gauge (94-02)
V = Voltage gauge (94-02)
S = Speedometer and Tachometer (94-02)
S = Transmission Temperature gauge (1999-02 NewBS trucks only)
T = Engine Temperature gauge (94-02).
If your fuel gauge needle was way off you will have to get access to a new fuel tank sender, hook it up and use it to calibrate the empty, 1/2, and full positions accurately. You can similarly re-calibrate major differences in the other gauges by replicating the source sensor input.
*The eBay and Amazon search links below are paid links, for which I may be compensated and earn a commission, if you choose to buy the parts and tools shown in this video thru them:*
Those still selling the "F" new - [ Ссылка ] or [ Ссылка ] or [ Ссылка ] and one selling rebuilt - [ Ссылка ]
C calibration: [ Ссылка ]
S calibration: [ Ссылка ]
All calibrations (skip over the yellow used ones unless they are rebuilt): [ Ссылка ]
GM 25089350 / ACDelco part number PC195 (replacement instrument cluster bulb) at eBay: [ Ссылка ]
Alternatively Dorman has a complete remanufactured cluster for these trucks. Dorman 599-350 for auto & Dorman 599-460 for manual trans: [ Ссылка ]
Here's the GM service manual: [ Ссылка ]
*NOTE:* It is very important you first eliminate a faulty fuel sender, bad grounds between your PCM and the fuel sender & the instrument panel. Your fuel sender is sending an analog signal to the PCM. The PCM is converting that to a digital square wave signal it sends to the cluster. The aircore motor for the fuel gauge is calibrated with a dampening fluid to smooth out the high and low points of this digital square wave signal. When that fluid degrades, the twitching begins. The gauge is otherwise accurate, until the aircore motor completely fails internally and then points off the gauge.
_And if I've saved you some $$ here, consider some coins for the coffee tip-jar!_ [ Ссылка ]
Chapters:
0:00 - Problem overview
1:25 - Removing the IP cluster
8:32 - IP cluster disassembly / aircore motor removal
14:37 - Replacement aircore motor installation
22:59 - IP cluster adjustments and reinstallation
#drshock
_Disclaimer: DrShock, the alias for the human content creator for this YouTube channel, is not responsible for any damages, injuries, losses, or liabilities associated with any repairs, upgrades, or maintenance performed on yours, or any other, vehicle whatsoever. No warranty, express or implied, is made as to the accuracy or completeness of any information provided within this channel. Viewing and using the “as-is" information of this channel is totally at your own risk. Always wear personal protection equipment and follow appropriate vehicle manufacturer service manual guidelines with original manufacturer parts only when performing any repairs, upgrades, or maintenance upon any vehicle._
