WEBSITE: [ Ссылка ]
YouTube Video Index -- A list of all of my videos: [ Ссылка ]
FOR THE POLARIS 360:
Polaris 360 Setup Video,Review & Tips: [ Ссылка ]
Polaris 360 Is Not Moving (Adjusting RPM): [ Ссылка ]
RELATED VIDEOS:
Polaris Stuck in Corner, Changing the bearings-Polaris360, 380: [ Ссылка ]
For changing the wheel bearings watch: [ Ссылка ]
How To Change All Eight Bearing in Your Polaris 280: [ Ссылка ]
For replacing the Backup Valve: [ Ссылка ]
For replacing the Hose Sweep: [ Ссылка ]
Polaris Quick Disconnect, Filter screen cleaning: [ Ссылка ]
Polaris Hose Length Guide: [ Ссылка ]
Changing Wheel (Polaris 180, 280 Not Moving): [ Ссылка ]
Polaris 280, 360, 380 Feed Pipe Assembly: [ Ссылка ]
Polaris 360, 380 Belt Replacement: [ Ссылка ]
Polaris 280 (180) Drive Shaft Assembly: [ Ссылка ]
NOTES:
It is a great cleaner if your pool is plumbed for it (separate booster pump). I also offer some troubleshooting tips.
First, you must have a separate pump plumbed in for the Polaris cleaner or you cannot install this cleaner. It needs it's own pump to work off the pressure (return) side of the pool verse the suction (skimmer/side port) side.
I have several customers with these cleaners installed (Two with Polaris 180 models which means that after 25 years they are still working fine) and all work off the same principal. The Polaris pump sends high pressure to the line the Polaris is attached to spinning the wheels and moving the cleaner. Every few minutes the Backup valve activates and reverses the cleaner (prevents it from getting stuck in one area).
Here are some troubleshooting tips:
Hose length is important. Too much hose and the cleaner will not work properly.
The Back-up Valve must be installed 14-20 inches from the cleaner and the water opening (where water shoots out of) must be facing the cleaner and not away from it. These valves tend to fail often. To know if it is working properly, lift it out of the water when the Polaris is running. If water is continuously shooting out and never stops, it has failed and you need a new one, otherwise the Polaris will not run.
The Quick Disconnect that attaches the Polaris to the wall also has an adjustment on it, make sure it is not all the way open or there will not be enough pressure. They tend to crack under the pressure so check it periodically to see if water is shooting out of it from a crack.
Sometimes when you clean the filter, some element will enter the Polaris return line. Simply disconnect the wall connector and clean out the small debris basket (looks like a Thimble).
If you find the Polaris on it's side in the bottom of the pool, the rear float has probably failed and is full of water. Simply remove it and install a new one. These are the most common problems you will have.
If the cleaner starts and runs for a few seconds then stops, then runs again and stops; check the skimmer basket & pump basket for debris (possibly low water too), if pool does not run the Polaris will not either since it works off the return water pressure.
If the Polaris hose is tangled and doesn't seem to unwind, just add a Swivel to the hose by cutting the hose with a blade, and inserting a swivel with 2 nuts to hold it in. Make sure the arrow on the swivel is pointed towards the Polaris and don't add a swivel within 10 FT of the Polaris (otherwise it will do 360 all day).
Note: Also if the Polaris wheels are not moving, more than likely the bearings are bad, very easy to change. Just take off the plastic nut, the wheel comes off, pop the old bearings out, pop in the new ones and you are set. If you have a Polaris 360 or 380 the drive belt may also be worn or broken. I posted a video that walks you through the replacement of the belts.
Mrdgvb1 Social Media Links:
Google +: [ Ссылка ]
Blogger: [ Ссылка ]
Facebook: [ Ссылка ]
If you found this video helpful, please visit my website, any donation is greatly appreciated.
WEBSITE: [ Ссылка ]
Ещё видео!