[ Ссылка ] : The Quick-Step Incizo profile can also be used to finish your stairs Seamless and subtle:
matching colour to your floor and a discrete transition. Applicable to any kind of staircase: straight or turning, with or without stair nose, flush or non flush Simple and fast Unlimited solutions for your stairs with the Quick-Step INCIZO PROFIlE
This stair profile is available in a pattern and surface structure that perfectly match your floor. To be installed in combination with the appropriate aluminium sub-profile. (To be ordered separately).Quick-Step's patented Incizo profile is a multifunctional finishing tool. One and the same profile can be used for all the finishes your floor needs.5 different applications with 1 product Practical You create the profile you need for a perfect finish to your floor Economical You can use any spare pieces of profile for other purposes, you won't have any excess profiles or leftovers Simple You always have the right solution at hand No inconvenient seams in comparison with other types of multifunctional profiles WARNING
o READ AND FOLLOW THE SAFETY INSTRUCTIONS INCLUDED WITH POWER TOOLS USED.
o SAFETY GLASSES SHOULD BE WORN AT ALL TIMES. o Only for use in residential
applications . - Double-check you have ordered the correct aluminium subprofile for the
Quick•Step® floor of your choice. - Clear the stairs of debris, making sure that all stairs are clean and level. - Use screws of 2,5 mm diameter. Drill diameter should be 3 mm. - Decide which stairs you want to obtain using the table, then concentrate on that type of finish, following the key as indicated in the table.
Installation
1.Start at the top of the stairs and work downwards.
2. Prepare 2 spacers per stair tread. Important: the spacers should have a thickness of the Quick•Step® floor you use, plus 2 mm. This will enable you later to easily insert the tread plank under the stair riser plank.
3.Measure the riser.
4A-4B. Saw a plank to the right size. If needed, click 2 planks together and only saw the tongue of the upper plank. *For type H, saw the tread plank like this.
5. Apply glue to the plank.
6. Put the plank against the riser. The groove should be behind the spacers. Repeat 1-6 for the rest of the stairs.
7. Measure the tread.
8. Saw the aluminium subprofile to the right length.
9. Apply glue to the bottom of the subprofile.
10A-10B-10C-10D. Install the subprofile on the tread. Screw it to the stairs, with an interval of 15 cm. Make sure the screws are well countersunk.
11A-11B. Saw a plank to the right size. If needed, click 2 planks together and only saw the groove of the last plank. *For type H, saw the riser plank like this.
12. Saw the Incizo® profile to the right length.
13. Cut the plastic insert to the right length (plastic insert is included in the aluminium subprofile packaging).
14. Push the insert into the groove of the Incizo®. Way of inserting depends on floor thickness,carry out as indicated on the illustration. Quick•Step® Parquet / Quadra UF406 -- UF1018: Apply glue to the tongue of the plank.
15. Apply glue to the subprofile and the rest of the tread. Apply in rows of +/- 3 mm.
16. Spread the glue out well on the subprofile (e.g. by means of a brush).
It is important to move to the next steps without delay, so the tread is still
adjustable when installing the Incizo® profile.
17A-17B. Install the tread plank. Do not press too firmly, so the plank does not tilt but stays nicely
flat. * For type H, install the riser plank like this.
18. Apply glue on both sides of the Incizo® foot.
19A-19B-19C-19D. Stick the Incizo® profile onto the subprofile and adjust the Incizo® and the plank nicely for a level result. Repeat installation for the rest of the stairs.
After installation, do not walk on the stairs for at least 24 hours.
20. Cut off part A of the Incizo® with the Incizo® knife -- see instructions included in Incizo® packaging.
Side finishing (only for laminate floors)
Half-open stairs can be finished with Incizo®, on the side of the plank with the tongue. Miter both the Incizo® and the aluminium subprofile and install as explained above.In certain cases an expansion joint is required: transition toa lower part of a room by
means of a tread, transition to another type of floor at the top of the staircase,...Obligatory non-flush installation of the Incizo® stair profile to cover an expansion joint.
