DIY Cup Turners. In this video i show you the steps i took to build this 4 cup rotisserie turner. I milled this lumber from a log of Eastern Red Cedar, then cut the lumber to size with the miter saw, ran the pieces through the thickness planer, ripped the pieces to size on the bandsaw, drilled holes for the motors, drying rack holes, cut electrical box holes, installed electrical boxes, ran electrical wire to each box, wired switches, I made TYC motor to PVC adapter plugs on the lathe, and put it all together. If you have any questions post a comment below.
If you found this video helpful Please Like & Subscribe, Share & post comments. If this video saved you money please send me a tip with super thanks, it will help me get paid for making these videos. Thanks for watching! Until next time!!
If you want to support the channel
Willow's World of DIY Tumblers & Katie's custom Tumblers:
[ Ссылка ]
Some of the links below are affiliate links. If you purchase through these links, it won’t cost you any additional cash, but it will help to support my channel and might save you money on some products. Thanks!
Parts list:
4 - 3/4" male PVC adapter: [ Ссылка ]
4 - 3/4" Female PVC adapter: [ Ссылка ]
1 - 10' stick of 3/4" PVC pipe
4 - small Foam football 20oz and smaller: [ Ссылка ] or 32oz tumblers: [ Ссылка ]
4 - TYC motor: [ Ссылка ]
4 - coupling connectors: [ Ссылка ]
4 - single gang electrical box: [ Ссылка ]
4 - 15 amp 120V single-pole switch: [ Ссылка ]
4 - switch plate covers: [ Ссылка ]
12ft of 14 gage wire: [ Ссылка ]
Electrical tape super 33+: [ Ссылка ]
38 - 3" exterior screws: [ Ссылка ]
8 - 1-1/2 wood screws: [ Ссылка ]
8 - 1/2" wood screws
Lumber dimensions:
1 - 7" x 48" x 1-1/2" (back piece)
1 - 7" x 48" x 1" (front piece)
1 - 5" x 48" x 3/4" (top piece)
4 - 9" x 12" x 1-1/4" (bottom pieces)
4 - 4" x 5-1/2" x 1-1/4" (pipe rest pieces)
( I built this cup turner with a 1-1/2" x 7" x 48" piece of lumber in the back to give it enough weight in the back to counter weight the cups being turned. This cup turner is very stable and we haven't had any problems with it.)
Product Links:
Wood Mizer Saw Mill: [ Ссылка ]
Speed square: [ Ссылка ]
Ridgid Miter Saw: [ Ссылка ]
Jet Bandsaw: [ Ссылка ]
Ridgid Thickness Planer: [ Ссылка ]
Drill Press: [ Ссылка ]
Freud Forcener Bits: [ Ссылка ]
Belt & Disc Sander: [ Ссылка ]
Belt Sander: [ Ссылка ]
TYC motors: [ Ссылка ]
2" Hole Saw: [ Ссылка ]
2" Forstner bit: [ Ссылка ]
Dewalt Random Orbital Sander: [ Ссылка ]
Hammer Drill: [ Ссылка ]
Drill Bit set: [ Ссылка ]
Shop Towels: [ Ссылка ]
Kobalt 16' Tape Measure: [ Ссылка ]
Kobalt 25' Tape Measure: [ Ссылка ]
Kershaw Chive 1.9" Pocket Knife: [ Ссылка ]
Kershaw Scallion 2.4" Pocket Knife: [ Ссылка ]
Kershaw 1600DAM Chive 1.9" Damascus Pocket Knife: [ Ссылка ]
20oz tumblers: [ Ссылка ]
Music:
Song
Summer Night - LIQWYD
[ Ссылка ]
Song
Morning - LIQWYD
[ Ссылка ]
Song
GLOW - LIQWYD
[ Ссылка ]
Song
With you - LIQWYD
[ Ссылка ]
Disclaimer:
Willow’s World of DIY assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Willow’s World of DIY recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, expensive electronics, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Willow’s World of DIY, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Willow’s World of DIY. Only attempt your own repairs if you can accept personal responsibility for the results, whether they are good or bad.
Ещё видео!