Find the parts used in the video on CarParts.com just there [ Ссылка ]

Our video shows you how to change the rear brakes on your 09-14 F-150. You will need to lift the vehicle, press the piston, remove the brake disc and follow the next steps described below. Take your 10 mm wrench and your wheel lug wrench and let's get started!

⚙️ NEEDED CARPARTS AND PRODUCTS
- Brake pad set : [ Ссылка ]

- Brake cleaner : [ Ссылка ]

- Copper grease

💪 TIGHTENING TORQUES
Lower slide pin and stop rubber balancer :
- 2009 through 2011 models : 22 Ft-lbs
- 2012 and later models : 24 Ft-lbs

🛠 TOOLS
The toolbox recommended by CARPARTS.COM to repair your Ford F-150 :
- [ Ссылка ]

List of the tools we used to replace the rear brake pads on a Ford F-150 :
- Hydraulic jack : [ Ссылка ]
- Jack stands : [ Ссылка ]
- Wheel lug wrench
- Big flat head screwdriver
- 10mm spanner
- Brake Wind-Back Tool : [ Ссылка ]
- Flat head screwdriver
- Wire brush
- Torque wrench : [ Ссылка ]
- Cloth

Don't forget to subscribe : [ Ссылка ]

🛻 COMPATIBLE VEHICLES
The operation and tools displayed in the video should be available on the following vehicles :
- 2009 Ford F150
- 2010 Ford F150
- 2011 Ford F150
- 2012 Ford F150
- 2013 Ford F150
- 2014 Ford F150

📽 🛠 USEFUL VIDEOS 🛠 📽
- How to jack your Ford F-150 safely : [ Ссылка ]

- How to replace front brakes, rotors and pads (Complete guide) 🚘 : [ Ссылка ]

⚠️ CARPARTS.COM'S INFOS
- Once the operation is completed, you'll need pump slowly on the brake pedal a few times until feeling a strong resistance from the pedal. The aim being to bring the brake pads closer to one other.

- Don't burn yourself on the pads if you've just gone for a drive as braking creates friction and long-lasting heat.

- Drive smoothly and avoid sudden braking for the first 30 miles or so, to avoid glazing the new pads.
What do we mean by "glazing new brake pads"? Brake pads are made of a material that needs to be run-in when new. If this procedure is not done properly, when braking too hard, the material overheats and hardens. Consequently, the brakes become less effective.

- For this operation, it is essential to have a brake calliper windback tool, which is a specific tool that allows you to press the piston into the caliper but also to make it turn on itself to reset the slack adjuster of your handbrake.

🚨 DISCLAIMER
This video is for entertainment purposes only. Carparts.com, Inc. disclaims all damages including, but not limited to, actual, consequential, and/or punitive, for any liability, claim, or any other injury or cause related to or arising from any information or lack thereof posted in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All mechanical car projects entail some risk. It is the sole responsibility of the viewer to assume this risk. If you are in doubt, please consult a licensed mechanic in your area.

📚 CHAPTERS
0:00 Intro
0:10 How to pull up your F150
1:04 Remove the brake caliper
1:56 Remove the pads
2:17 Press the piston
2:50 Remove the anti-rattle clips + Cleaning
3:09 Prepare and insert the new pads
3:47 Put the caliper back + Tightening
4:35 Safety tips
4:45 Put your F150 back on the ground
4:56 Tips

свернуть