Solar Light Tower - 30' Tower - 7.5' Trailer - (3) Panels, (4) LED Lamps - (8) 250aH Batteries - Wind Generator
[ Ссылка ]
The Larson Electronics SPLT-.9K-LM30-WG.04-4X100LTL-AT-BC-M1 solar powered LED light tower provides a safe and effective way for operators to quickly deploy intense LED illumination to elevations up to thirty feet. This solar light plant features a telescoping light tower that folds over for easy transportation, a rotating boom that allows for 360° rotation and a removable mast head for storing the four LED light fixtures when not in use. The unit features three 300-watt solar panels, a 400-watt wind generator and a deep cycle AGM battery bank. The entire assembly is mounted onto a 7.5` single axle trailer, allowing operators to transport this solar light tower from location to location.
This solar light tower includes three solar panels, wind generator, solar charging system, deep cycle AGM battery bank, rapid battery chargers and manual crank up mast mounted on trailer with outriggers. The 0.9 kW solar generator system offers 72 hours of continuous-run battery capacity back-up in case of emergency. This system delivers 24 volts for lighting mounted atop the 30` telescoping light mast.
Light Mast: This telescoping three stage steel light mast from Larson Electronics is designed to allow operators to quickly and safely deploy four LED light heads in locations where this equipment must be elevated to heights up to 30` for effective coverage. This light boom can be extended to 30` above the trailer floor for maximum area coverage, and collapsed to 13.5` for applications where a smaller footprint is required. The tower is constructed of square steel tubing with a base section 6.6` in length and 6" by 6" by 3/16" thick, lower section 6.78` in length and 5" by 5" by 3/16" thick, middle section 6.93` in length and 4" by 4" by 1/8" thick, upper section 7.08` in length and 3" by 3" by 1/8" thick, and top section 7.58` in length and 2" by 2" by 1/8" thick. Each section has a 1`+ overlap. The mast is extended to its full height using an included 1,000lb rated hand winch with 3/16" galvanized steel cable.
A 44" wide and 2" by 2" by 1/4" thick mounting plate is attached to the upper section of the mast which provides a strong and stable platform for the equipped LED light fixtures. When elevated to its full upright position, the mast can be rotated a full 360°. By loosening the T-Handle, operators can rotate the mast with easy in either direction. The mast can be positioned in one of four different positions, and locked back in place by re-tightening the T-handle. The mast itself spins freely with easy, and can typically be rotated with a single hand. The LM series of towers are powder coated with glossy blue finish for corrosion resistances and aesthetics.
The LM family of telescoping towers feature a proprietary mast guidance system, which provide increased stability during high winds. Five 1,000 lbs hand crank leveling jacks are used for leveling. The jacks can be leveled by hand crank or attachment provided for power drills. These outriggers can be extended 2` out from the side of the trailer for added stability. When lowered to 13.5`, the mast can withstand winds up to 125 mph. Custom builds can be provided for higher wind speed resistance when fully raised.
Trailer Assembly: The entire assembly is mounted to a 7.5` by 7`, single axle trailer via six 1/2" anchor bolts. The two wheel, powder coated steel trailer is equipped with 3,500 lbs axle and leaf springs with 15" trailer tires. Lunette ring pintle pitch, two standard safety chains, and 7-pin flat trailer plug allow for easy hookup and towing. Forklift pockets and tie down rings on the trailer are available for lifting or shipping. The trailer tongue can be removed for long term deployment and a 4.5` x 7.5` footprint. A rugged and waterproof job box is included, safely secured to the trailer. Five outriggers allow operators to level the trailer and provide stabilization during deployment. All trailer lighting complies with DOT/FMVSS regulations.
At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 1-800-240-2508 or message sales@larsonelectronics.com for more information about our custom options tailored to meet your specific industry needs.
