today i will guide you how to control a stepper motor with an arduino and a4988 stepper driver,
we will see how to control its rotation speed with a potentiometer, and change its direction of rotation with a push button.
components we will need;

a stepper motor,
an a4988 stepper motor driver,
an arduino board,
a 100k potentiometer
push button
100mf capacitor
breadboard and connecting wires.

i have also written a code to run the motor on various speeds using a potentiometer to adjust the motor speed.

you will find all the diagrams and arduino files here:

[ Ссылка ]
NOTE: arduino code is in folders above schematics :)

buy stepper motors for cheap here:

Stepper Motor NEMA 17: [ Ссылка ]




buy links for parts:

(Global):

Arduino UNO micro USB version: [ Ссылка ]
Stepper Motor NEMA 17: [ Ссылка ]
A4988 Driver: [ Ссылка ]
Potentiometer 100Kohm: [ Ссылка ]

India:

Arduino UNO: [ Ссылка ]
Stepper Motor NEMA 17: [ Ссылка ]
A4988 Driver: [ Ссылка ]
Potentiometer 100Kohm: [ Ссылка ]





the A4988 stepper driver module has total 16 pins

the vmot and ground pins are for the external power for the motor,
you cannot power the motor from the arduino as it requires a minimum of 8-35 volts
i use a 12 volts 2 amp external power supply. make sure you use a decoupling capacitor to avoid any unnecessary noise.
the next 4 pins are of the stepper motor.
you have to connect the pins with the right polarity, otherwise your motor wont work and make loud noises.
you can determine the polarity of the motor using your multi-meter
Each pair of same phase should have no resistance when measured with a multi-meter, so you have to check the pairs which have zero resistance
and connect positive and negative of phase A to 1a and 1b, and accordingly for phase b


it is better to check the polarity in the manufacturer information for your motor to avoid this hassle.
you can also connect multiple stepper motors for similar actions in parallel until you do not exceed the current limit

next you have to connect the reset and sleep pin to activate the driver.
the a4988 uses 3.5-5 volts power so you can power it from the arduino 5v output
connect the digital4 pin of the ardiuno to the direction pin and d3 pin to step pin of the driver.
the ms1,2,3 pins are for enabling microstepping.
you can connect 5 volt input to the pins to enable microstepping. there are 5 different modes for micro-stepping as shown in the table.
it is also important to limit the current to the motor.
you can do so by setting the potentiometer on the driver to around 30 degrees clockwise for 0.5 amps

first we will run a simple code to run a full rotation and pause for 1 second.
upload the code and you see the motor running.
if not,make sure you have connected all pins correctly. and followed all the procedures

i have also written a code to run the motor on various speeds using a potentiometer to adjust the motor speed.
you have to connect the potentiometer wiper pin to a0 pin of the arduino, and connect 5v input in the first, and ground the third pin
i have another code in which you can toggle the direction of the motor using a push button.

hope you enjoyed the video, please do like share and subscribe, and thanks for watching!


Solder Iron i Use: [ Ссылка ]

Helping Hand Magnifier: [ Ссылка ]



check out my other projects:


DIY Lab Bench power Supply: [ Ссылка ]

DIY Dremel Tool: [ Ссылка ]

Arduino 3D Printer : [ Ссылка ]

DIY on off Timer: [ Ссылка ]

DIY Quadcopter: [ Ссылка ]


#steppermotor #steppermotorcontrol #steppermotortutorial #howtocontrolsteppermotor

свернуть