Ask This Old House host Kevin O’Connor works with maker Jenn Largesse to demonstrate an interesting technique on a trim router.

SUBSCRIBE to This Old House: [ Ссылка ]

Time: 15 minutes or longer, depending on the size of the circle
Cost: $30 and up
Skill Level: Beginner

Tools:
Trim router [[ Ссылка ]]
Drill driver [[ Ссылка ]]
Countersink bit [[ Ссылка ]]
Spade bit [[ Ссылка ]]
Measuring tape [[ Ссылка ]]
Clamps [[ Ссылка ]]

Shopping List:
¼” board [[ Ссылка ]]
Wood to cut a circle into (can be any species or dimension) [[ Ссылка ]]
Nail [[ Ссылка ]]

Steps for Cutting a Perfect Jig:
1. Before doing any work to the router, be sure that the battery has been removed or the router has been unplugged.
2. Remove the base of the router by unscrewing it by hand or with a drill driver.
3. Place the router base on the ¼” board and trace the screw holes and the opening for the bit onto the board.
4. Drill holes in the locations of the screw holes using a countersink bit. The countersink bit will ensure the screws can sit flush with the base of the router, which will be important for cutting.
5. For the center hole, drill it out using a spade bit.
6. Determine the desired radius of the circle and then transfer that measurement to the board. Use the center of router bit hole as your starting point.
7. Drill a small hole at the measurement of the radius. This will eventually accept a nail and will act as a pivot point.
8. Attach the board to the router in place of the base. The screws and screw holes should all line up with the ones drilled in the board.
9. Secure the board being cut to the work surface with clamps or screws.
10. Determine the center of the board being cut by measuring diagonally from corner to corner. The intersection of the two lines is the center.
11. Place the router with the jig onto the board. Line the nail from the pivot point up with the center of the board and hammer it into the board. Be sure to not secure it too tightly, as you will still need the router to move easily.
12. Set the router bit just slightly past the depth of the jig.
13. Turn the router on and start cutting the board. Turn the jig at the pivot point as you cut. This will create a circle.
14. After the first pass, lower the router bit again and make a second pass.
15. Continue this process until the circle has been cut.

Resources:
Jenn demonstrated how to cut a perfect circle using a RYOBI ONE+ cordless trim router [[ Ссылка ]] ([ Ссылка ]). 

Jenn Largesse is the editor of multiple DIY blogs, including House One ([ Ссылка ]) and Build Basic ([ Ссылка ]).


About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Jenn Nawada.

Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free.
[ Ссылка ]
 
Plus, download our app for streaming full episodes to your connected TV, phone or tablet:
[ Ссылка ]

Follow This Old House and Ask This Old House:
Facebook: [ Ссылка ]
Twitter: [ Ссылка ]
[ Ссылка ]
Pinterest: [ Ссылка ]
Instagram: [ Ссылка ]

Watch the full episode:
[ Ссылка ]

How to Cut a Perfect Jig Circle | Ask This Old House
[ Ссылка ]

свернуть