In this video I take a look a deep dive into the workings of this "basic" police strobe light kit that I got from Aliexpress.

Get the kit here: [ Ссылка ]

Timestamps
00:00 Intro
01:00 Initial Thoughts
15:45 Soldering
26:15 Test
28:15 Troubleshooting
32:15 How Each Component Works
43:22 Simulation
58:10 Magic Smoke Release
01:00:15 Future Improvements
_____

The circuit uses 555 timer and a decade counter IC CD4017. The 555 timer produces continuous pulses at the output. Decade counter 4017 counts the incoming pulses and activates its outputs i.e. for the first pulse Q0 becomes high and for second pulse Q1 becomes high and so on again for 10th pulse Q0 state becomes high.

__________

## What each component does

### NE555

A simple IC that produces single rectangular pulses or long time delays. It can be used for many things. In this instance we use it to produce a rectangular wave, which we'll use as a pulse to get the next device to act based on the pulses. Servers as the 'clock' for our circuit.

### CD4017

A decade counter is a counter that goes from 0 to 10, which for us is Q0 to Q9.

For every incoming pulse the output state of the decade counter is incremented.

### Diodes 1N4145

They provide reverse voltage protection to the CD4017. The datasheet states they can handle 1000V .

### NPN Transistors

Based on the outputs of 4017 IC, two transistors (NPN) switches the LED’s ON and OFF.

It does this by allowing the current to flow from the VCC and LEDs, through the transistor and then to ground.

Transistors can handle 1.5A

### LEDs

Standard LEDs 5mm diffused

RED LEDs require 1.6V - 2V

Blue LEDs require 2.5V - 3.7V

This is why the Blue LEDs didn't work on a lower voltage, the red LEDs were getting enough voltage but the blue ones weren't.

### Resistors

**100k Potentiometer**

Adjusts the frequency of the 555 timer. Which literally means it will increase or reduce the length of the pulses.

**10k R1, R2, R3**

The three resistors server as current limiting resistors.

R1 serves as a current limiting resistor to the 555 timer.

R2 and R3 serve as current limiting resistors to the base of the transistor.

**100 R4 & R5**

The listing states R2 and R3. In fact it is R4 and R5. They are 100ohm resistors. They control the brightness of led. Listing recommends 10-100 ohm.

### Capacitors

**C1 10uf**

Capacitor C1 charges through resistors R1 and R2. While the capacitor is charging, the output is high. When the voltage across C1 reaches 2/3 of the supply voltage C1 discharges through resistor R2 and the output goes low. When the voltage across C1 drops below 1/3 of the supply voltage C1 resumes charging, the output goes high again and the cycle repeats.

**C2 0.01uf**

C2 is the capacitor used to remove the noise.

__________

Hi, I'm Hamed, an Electrical & Electronics Engineering Student in Leeds, UK.

Visit my website at www.hamed.engineer

If you have any questions you can email me at hamed@hamed.engineer or just comment below.

Stuff You May Have Seen In My Videos
Oscilloscope £220: [ Ссылка ]
Elegoo Arduino Most Complete Kit £50: [ Ссылка ]
Elegoo Arduino Basic Kit £15: [ Ссылка ]
Soldering Iron Station £30: [ Ссылка ]
Handheld Oscilloscope £50: [ Ссылка ]
DIY Function Generator £9.99: [ Ссылка ]
Lavolta Power Supply £60: [ Ссылка ]
Eventek Power Supply £60: [ Ссылка ]

You Can Also Find The Above For Cheaper On Banggood/Aliexpress

свернуть