[ Ссылка ]
Introduction:
CrazybeeX series flight controller is the first 5in1 AIO flight controller which could handle 2s.It's a better upgrade flight controller for your whoops.
- Use to build a 1-2S compatible lightest 65mm/75mm/85mm brushless whoop or  2-3 inch ultra light toothpick.
Specification:
Brand: Happymodel
Model: CrazybeeX FR/FS/PNP V2.2
Item Name: F4 Flight Controller AIO ESC VTX Receiver Board
Weight: 4.4g
Flight Controller
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000 (SPI Connection)
Board Size: 28.5 * 28.5mm
Power Supply: 1S-2S battery input (DC 2.9V-8.7V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky receiver support D8/D16 (
Built-in 5V 1A BEC
Built-in voltage detection
Firmware Target:
CrazybeeX FR Version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FR
CrazybeeX FS version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FS
CrazybeeX PNP version: Recommend Betaflight 3.5.7 target CRAZYBEEF4DX
Onboard 5A 4In1 ESC
EFM8BB21
Power Supply: 1-2S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory Firmware: S_H_50_REV16_7.HEX
Default Protocol: DSHOT600
(CrazybeeX FR V2.2 Version)
Onboard Frsky SPI Receiver
SPI BUS Receiver Frsky D8/D16 Compatible
Support for Futaba S-FHSS (Need Betaflight 4.0.5 firmware or latest), Frsky_X_LBT(EU-LBT) 
Channels: 8CH / 16CH
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
(CrazybeeX FS V2.2 Version)
Onboard Flysky SPI Receiver
SPI BUS Receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8CH (AFHDS) or 14CH (AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
Failsafe support
(CrazybeeX PNP V2.2 Version W/O on Board Receiver)
No Onboard SPI Receiver
Onboard 5.8G 40CH VTX
Output Power: 25mw~200mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
Smartaudio ready
Default vtx_power is 3
Should set vtx_low_power_disarm = ON to reduce the high temperature when test on the ground.
Onboard Voltage and Current detector
Voltage Meter scale “110”
Amperage Mete scale “1175”

Features:
CrazybeeX FR V2.2 Bind procedure:
Make the on board receiver get into bind mode: Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; Or use bind code to bind :For 3.5.7 version firmware Plug USB and then connect Betaflight configurator and then move to CLI tab , type “Frsky_bind”, the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.0.x the bind code is “bind_rx_spi” ,For 4.1.x or 4.2.x the bind code is “bind_rx”
Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink.   The red LED wouldn't blinking when binding with some new ACCESS firmware frsky radio  , but the bind is actually successful , need to go to CLI command and type “save” to finish the binding .
CrazybeeX FS V2.2 Bind procedure:
Make the on board receiver get into bind mode: For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid.
SPI Receiver option:
Frsky_D compatible with Frsky D8 protocol
Frsky_X compatible with Frsky non-eu D16 protocol
Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
SFHSS compatible with Futaba S-FHSS protocol
A7105_FLYSKY_2A compatible with Flysky AFHDS-2A protocol
A7105_FLYSKY compatible with Flysky AFHDS protocol



BUY [ Ссылка ]

свернуть