LED Strip Replacement Tutorial
CLICK HERE for replacement LEDs: [ Ссылка ]

SKU: sj-BN96-29074A/BN96-29075A
Part Type: LED Strips
Part Number: BN96-29074A/BN96-29075A
Part Usage: LED/LCD
MFR Part Number 1: Samsung BN96-29074A
MFR Part Number 2: Samsung BN96-29075A
Board Number(s): LM-00001M, LM-00001L, SAMSUNG 2013SVS60 3228N1 B2 L07 REV1.7 131015, SAMSUNG 2013SVS60 3228N1 B2 R07 REV1.7 131015, D3GE-600SMA-R2, D3GE-600SMB-R1
Panel Sticker Number: CY-DF600CGSV4H, CY-DF600CGSV2H, CY-DF600CGSV3H, CY-DF600CGSV6H
Panel Manufacturer: Samsung
Brands: Samsung
Important Message: PLEASE NOTE: The models shown may use various different sets of LED Strips. Please match the original strips in your TV to those in the photo before ordering. 29074A or 29075A can usually be found printed on the small barcode stickers on the strips.
TV Part Types: LED Light Strip
Samsung TV Models:

UN60J6200AFXZC
UN60FH6003HXPA
UN60FH6003GXZS
UN60FH6003GXZD
UN60FH6003GXPE
UN60FH6003FXZX
UN60FH6003FXZP
UE60H6273SSXZG
UE60H6273ASXTK
UE60H6204AKXXE
UN60FH6003KXZL
UN60FH6200FXZC
UN60H6203AFXZC
UN60H6153AFXZX
UN60H6103AHXPA
UN60H6103AGXZS
UN60H6103AGXZD
UN60H6103AGXPR
UN60H6103AFXZX
UN60H6103AFXZP
UN60FH6200FXZX
UE60H6203AWXZF
UE60H6203AWXXN
UE60H6203AWXXH
UA60H6003ARPXD
UA60F6088AJXXZ
UN60EH6003FXZC
UN60J620DAFXZA NS02
UN60J6200AFXZA EA03
UN60J6200AFXZA MH01
UN60J6200AFXZA NS02
UN60J6200AF/XZC NS02
UN60H6203AFXZA GH02
UN60FH6200FXZA HH01
UN60FH6003FXZA HH01
UA60H6003ARXEG
UA60H6003ARXRQ
UE60H6203AWXXC
UE60H6203AWXTK
UE60H6203AKXZT
UA60H6203AKXXV
UA60H6203AKXXS
UA60H6003ARXZN
UA60H6003ARXWT
UA60H6003ARXUM
UA60H6003ARXTW
UN60EH6003FXZA IH02

Try all repairs and troubleshooting at your own risk.
In this video we will show how to replace the Samsung LED strips that we have listed on the screen. Be sure to match the important information on our product page, when replacing LED strips to be sure the replacement strips are compatible with the originals.
When replacing LED strips, you will have to remove the panel.
Removing the panel can be very difficult. If your TV panel is damaged during the replacement process, you will have to get a replacement TV.
We will start by removing both pieces of the back cover off the TV.
Remove the cover over the T-con board.
Use tape to hold the speakers in place.
Disconnect the key controller and secure it to the chassis with some tape.
Flip the TV over and using a five in one tool or a putty knife or something similar disconnect the bezel from the chassis.
Disconnect the buffer boards from the t-con.
Release the buffer boards from the tabs that secure it. be very careful as this board is very fragile.
Using painters tape or something similar, tape the buffer board to the panel.
Removing the panel is very important. But you must be sure the panel does not flex or bend. If the panel cracks or breaks, you will need to replace your entire TV.
We recommend using a suction cup to lift and remove the panel, but you could also use some thin sheets of plastic or something similar to lift it away.
Using a five in one tool, or putty knife or something similar, pry the panel frame from the chassis.
Separate and lift away the layers of diffusion. You can tape them in the corner to keep them together and in order.
There are some clips that hold the reflector sheet to the panel. They can be released on the board side of the chassis and then pulled out from the panel side. Be sure to look underneath the boards if you cannot locate all of the clips.
Remove the reflector sheet from the chassis. The reflector sheet may be sticky on the backside that is attached to the chassis. Be very careful when removing the sheet, so you do not tear it.
There is a little bit of tape holding these original strips to the chassis. Remove the strips of tape and disconnect the LED strips from the cable, before removing them.
Install the replacement LED strips. To help hold the replacement strips in place, we are using some double sided tape.
Align the strips into position and then connect them to the wire.
Align the reflector sheet on the chassis and reinstall the clips.
Install the layers of diffusion.
Reinstall the frame.
Lift the panel back into position and be sure the corners align correctly.
Release the buffer board and lock it back into position.
Reconnect the buffer boards to the t-con.
Reinstall the bezel and be sure it is properly aligned.
Reinstall the keypad controller.
Reinstall the t-con board cover.
Reinstall both of the back covers.

PLEASE NOTE: The models shown may use various different sets of LED Strips. Please match the original strips in your TV to those in the photo before ordering. 29074A or 29075A can usually be found printed on the small barcode stickers on the strips.


TV Repair Made Easy™
© 2017 ShopJimmy.com, LLC.

свернуть