This is how to change the oil and oil filter on a 2009 - 1015 Toyota Corolla 1.8L. Very, very simple.
BUY ON AMAZON:
[ Ссылка ]
#socaltoyota #bundysgarage #corollaoil
2009 Toyota Corolla
2010 Toyota Corolla
2011 Toyota Corolla
2012 Toyota Corolla
2013 Toyota Corolla
2014 Toyota Corolla
2015 Toyota Corolla
Before you begin changing your Toyota Corolla’s oil, make sure you have a level surface to work on. A clean and well lit area is ideal. Also, make sure you have an assortment of mechanic’s tools including a socket set and oil filter socket/tool. Lastly, make sure you have all the items you need to change oil like:
Oil collection pan
4 Quarts of oil
Oil filter
Funnel
Rags
Also, there is some debate about how often you should change your oil. In the past, it was always 3 months or 3,000 miles. Toyota says to change the oil 6 months/5,000 miles unless it is 0W-20 synthetic oil. Then, it is 1 year/10,000 miles. Whichever side of the argument you fall on, it is important to be consistent.
Oil Change Process
In order to change the oil, follow these steps:
Climb under the Corolla and locate the drain oil plug. This sits below the engine.
Slide the oil collection pan under the drain plug. Using a 14-mm socket and socket wrench loosen the drain plug.
Oil should start draining from the engine and you can fully loosen and remove the plug to speed the process.
Once the oil is done, you will need to locate the oil filter.
Using an oil filter socket and socket wrench or removal tool, remove the oil filter.
Empty the oil from the filter into the pan and wait for any additional oil to finish draining.
Using a rag, wipe around the oil filter fitting on the engine block.
Next, grab a clean rag and apply some new oil on it. Using this oil, wipe around the edges of the new oil filter.
Install the new oil filter by reversing the removal instructions.
Insert the drain plug back in and tighten it down being careful to not over tighten it.
Open the hood and find the oil cap on top of the engine. Pour in 3.5 to 4 quarts of new oil. Take your time adding new oil to avoid making a mess and/or overfilling it.
After filling it up, check the dipstick to make sure you have the proper amount of oil.
Lastly, you will want to reset the maintenance light. In order to do that, turn the key to ACC, or accessory. Set your odometer on mileage, not trip, then turn off the key. Now press and hold the button you use to switch to trip, then turn they key back to ACC. The light should blink while you are holding the button down.
More About BundysGarage:
[ Ссылка ]
Questions, Comments, Concerns:
bundysgarage@gmail.com
Twitter:
[ Ссылка ]
@bundysgarage
On The Web:
[ Ссылка ]
Music by Randall Kent: As seen on NCIS
[ Ссылка ]
All Rights Reserved 2019
© Copyright 2019
Bundys Garage
All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: bundysgarage@gmail.com
DISCLAIMER - DISCLAIMER - DISCLAIMER
Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.
